Polyamid 12 ist der Standardwerkstoff für Druckluft- und Hydraulikleitungen mit hohen Druck- und Temperaturanforderungen. Geringe Wasseraufnahme, hohe Maßhaltigkeit, hervorragende Beständigkeit gegen Öle, Fette und Kraftstoffe — und eine Normzulassung für Druckluftbremsanlagen nach DIN 73378. Polyamide 12 is the standard material for compressed-air and hydraulic lines with demanding pressure and temperature requirements. Low moisture absorption, high dimensional stability, excellent resistance to oils, greases and fuels — and standard approval for compressed-air brake systems per DIN 73378.
Polyamid 12 (PA 12) ist ein teilkristalliner Thermoplast aus der Polyamidfamilie. Im Vergleich zu PA 6 und PA 6.6 hat PA 12 die geringste Wasseraufnahme aller technischen Polyamide — daher exzellente Maßhaltigkeit auch bei wechselnder Luftfeuchte. Zusammen mit hoher Schlagzähigkeit, niedrigem Reibwert und guter Chemikalienbeständigkeit ist PA 12 die erste Wahl, wenn Druck, Temperatur und Medienkontakt gleichzeitig hoch sind. Polyamide 12 (PA 12) is a semi-crystalline thermoplastic from the polyamide family. Compared to PA 6 and PA 6.6, PA 12 has the lowest moisture absorption of all technical polyamides — hence excellent dimensional stability even under changing humidity. Combined with high impact strength, low friction and good chemical resistance, PA 12 is the first choice whenever pressure, temperature and media contact are simultaneously demanding.
Polyamid-12-Rohre werden je nach Weichmacheranteil in zwei Gruppen unterschieden — geregelt durch DIN 73378. Beide Bauarten sind nach EG-Richtlinien recyclebar. Polyamide-12 tubes are split into two groups depending on plasticizer content — defined by DIN 73378. Both types are recyclable per EC guidelines.
Hochviskoses, weichmacherarmes PA 12. Höhere Steifigkeit (E-Modul ≈ 1500 MPa), höhere Druckfestigkeit. Ideal für Druckluftbremsen mit hohen Drücken. Vertreter: VESTAMID® L2140 NC.High-viscosity, low-plasticizer PA 12. Higher stiffness (tensile modulus ≈ 1500 MPa), higher pressure resistance. Ideal for compressed-air brakes at high pressures. Example: VESTAMID® L2140 NC.
Mit Weichmachern eingestelltes PA 12. Deutlich flexibler (E-Modul ≈ 400 MPa), kleinerer Biegeradius, leichtere Verlegung. Speziell für Öl- und petrochemische Anwendungen. Vertreter: VESTAMID® L2124 NC.Plasticized PA 12. Significantly more flexible (tensile modulus ≈ 400 MPa), smaller bend radius, easier routing. Especially for oil and petrochemical applications. Example: VESTAMID® L2124 NC.
Polyether-Block-Copolyamid auf PA-12-Basis — weichmacherfrei, hohe Schlagzähigkeit auch bei tiefen Temperaturen, gute Hydrolysebeständigkeit. Vertreter: VESTAMID® E55-S3.Polyether block copolyamide based on PA 12 — plasticizer-free, high impact strength even at low temperatures, good hydrolysis resistance. Example: VESTAMID® E55-S3.
Drei VESTAMID®-Typen aus dem Hause Evonik, die für die Extrusion von PA-12-Schläuchen und -Rohren eingesetzt werden. Werte aus den Original-Datenblättern (Evonik Operations GmbH). Three VESTAMID® types from Evonik used for the extrusion of PA-12 tubes and hoses. Values from the original datasheets (Evonik Operations GmbH).
| EigenschaftProperty | L2140 NC (HL) | L2124 NC (PHL) | E55-S3 (PEBA) |
|---|---|---|---|
| Typ-KlassifizierungType | PA 12-HL | PA 12-PHL | PA 12-Elastomer |
| E-Modul (trocken)Tensile modulus (dry) | 1500 MPa | 400 MPa | 215 MPa |
| Zugfestigkeit (trocken)Tensile strength (dry) | 44 MPa | 26 MPa | 38 MPa |
| ReißdehnungStrain at break | 140 % | 200 % | 200 % |
| Shore-D HärteShore D hardness | 75 | — | — |
| SchmelztemperaturMelting temperature | 178 °C | 169 °C | — |
| GlasübergangstemperaturGlass transition temp. | 45 °C | — | — |
| DichteDensity | 1,01 g/cm³ | 1,03 g/cm³ | — |
| WasseraufnahmeWater absorption | 1,6 % | 1,3 % | — |
| Brennverhalten (UL/IEC)Burning behaviour | HB | HB | HB |
| Norm-KonformitätStandard compliance | DIN 73378 | DIN 73378 | — |
Kennwerte gemäß ISO 527 / ISO 1183 / ISO 11357 an Probekörpern aus Spritzguss. Werte „trocken"; konditionierte Werte können abweichen. Values per ISO 527 / ISO 1183 / ISO 11357 on injection-moulded specimens. "Dry" values; conditioned values may differ.
Hochviskoses, hitze- und lichtstabilisiertes PA-12-Compound für die Extrusion von Druckluft- und Kraftstoffleitungen nach DIN 73378 (Typ PA 12-HL). E-Modul von 1500 MPa und Zugfestigkeit von 44 MPa machen es zur ersten Wahl, wenn maximale Druckfestigkeit gefragt ist. Shore D 75. High-viscosity, heat- and light-stabilized PA 12 compound for the extrusion of compressed-air and fuel lines per DIN 73378 (type PA 12-HL). Tensile modulus of 1500 MPa and tensile strength of 44 MPa make it the first choice when maximum pressure resistance is required. Shore D 75.
Weichmachermodifiziertes, hochviskoses PA 12 mit guter Maßkontrolle bei der Rohrextrusion (Typ PA 12-PHL). E-Modul von 400 MPa erlaubt deutlich kleinere Biegeradien — speziell entwickelt für Öl- und petrochemische Anwendungen sowie Druckluftleitungen, bei denen flexible Verlegung im Vordergrund steht. Plasticizer-modified, high-viscosity PA 12 with good dimensional control during tube extrusion (type PA 12-PHL). Tensile modulus of 400 MPa allows significantly smaller bending radii — specifically developed for oil and petrochemical applications as well as compressed-air lines where flexible routing is key.
Thermoplastisches Elastomer auf PA-12-Basis (Polyether-Block-Copolyamid). Frei von migrierenden Weichmachern, kein Versprödung und Altern. Sehr gute Schlagzähigkeit auch bei tiefen Temperaturen, gute Hydrolysebeständigkeit. Wo PA 12-PHL nicht weich genug ist, wird E55-S3 zur Brücke zwischen Polyamid und PUR. Thermoplastic elastomer based on PA 12 (polyether block copolyamide). Free from migrating plasticizers, no embrittlement or aging. Very good impact strength even at low temperatures, good hydrolysis resistance. Where PA 12-PHL is not flexible enough, E55-S3 bridges polyamide and PUR.
Standard für Druckluftbremsanlagen in Lkw, Bussen und Anhängern (DIN 73378:1996-02 und DIN 74324-1:1996-02). Auch für Kraftstoff- und Schmierstoffversorgungssysteme sowie Unterdruckleitungen. PA 12 ist die einzige Polymerklasse, die in diesem Sicherheitsbereich serienmäßig zugelassen ist.Standard for compressed-air brake systems in trucks, buses and trailers (DIN 73378:1996-02 and DIN 74324-1:1996-02). Also for fuel and lubricant supply systems and vacuum lines. PA 12 is the only polymer class with serial approval in this safety domain.
Druckluftleitungen im Niederdruckbereich, Mini-Hydraulik in der Mess- und Regeltechnik, Leitungen für flüssige und rieselfähige Stoffe. Vakuumgeeignet bis 12 × 9 mm. Schleppkettentauglich bei sorgfältiger Auslegung.Compressed-air lines in the low-pressure range, mini-hydraulics in measurement & control, lines for liquid and free-flowing substances. Vacuum-rated up to 12 × 9 mm. Drag-chain capable with careful design.
Beständig gegen Mineralöle, Kraftstoffe, Hydraulikflüssigkeiten, viele Lösungsmittel sowie Alkalien und Salzlösungen. Geringe Quellung, hohe Maßhaltigkeit auch bei wechselnder Umgebungsfeuchte.Resistant to mineral oils, fuels, hydraulic fluids, many solvents and to alkalis and salt solutions. Low swelling, high dimensional stability even under varying humidity.
Der zulässige Betriebsdruck eines PA-12-Schlauchs sinkt mit steigender Temperatur. Bei +50 °C steht typisch nur noch ca. 50 % des Drucks bei +23 °C zur Verfügung, bei +80 °C sind es ca. 34 %. Detaillierte Druckausnutzungstabellen stellen wir auf Anfrage zur Verfügung. The permissible operating pressure of a PA-12 hose decreases with rising temperature. At +50 °C, typically only about 50 % of the +23 °C value remains, at +80 °C about 34 %. Detailed pressure utilisation tables are available on request.
| NormStandard | InhaltScope |
|---|---|
| DIN 73378 | Polyamid-Rohre für Kraftfahrzeuge — Druckluftbremsanlagen, Kraft- und SchmierstoffleitungenPolyamide tubes for motor vehicles — compressed-air brake systems, fuel and lubricant lines |
| DIN 74324-1 | Druckluftbremsanlagen — Druckluft-Kunststoffleitungen, Maße und AnforderungenCompressed-air brake systems — plastic compressed-air lines, dimensions and requirements |
Hart oder weichgemacht, in 7 Standardfarben, als Meterware, Festlänge oder auf Trommel — wir liefern die passende Spezifikation. Rigid or plasticized, in 7 standard colours, as cut length, fixed length or on drum — we deliver the right specification.
Anfrage startenStart enquiry